Skip to main content
Vulnerability Database/CVE-2026-82933

CVE-2026-82933: mH-DEVELOPER Smart Home Information Disclosure

CVE-2026-82933 is an information disclosure vulnerability in mH-DEVELOPER smart home module that exposes credentials and tokens over unencrypted HTTP. This article covers the technical details, affected versions, security impact, and available mitigation strategies.

Published:

Disclaimer: This content was generated using AI. While we strive for accuracy, please verify critical information with official sources.

Sources: National Vulnerability Database, CISA KEV, Exploit-DB

CVE-2026-82933 Overview

CVE-2026-82933 affects the mH-DEVELOPER smart home module, which transmits its web interface and API traffic over unencrypted HTTP. Passwords, authentication tokens, and device commands traverse the network in cleartext. An attacker positioned on the same local network can intercept this traffic, harvest credentials and session tokens, and hijack active sessions to control the smart home module. The vendor fixed the issue in version 3.0.30. The weakness is classified as a cleartext transmission of sensitive information issue and corresponds to insecure communication design in the device firmware.

Critical Impact

Adjacent-network attackers can passively sniff credentials, tokens, and device commands, then hijack sessions and issue arbitrary commands to the smart home module.

Affected Products

  • mH-DEVELOPER smart home module versions prior to 3.0.30
  • Web interface component served over HTTP
  • API endpoint exposed over unencrypted HTTP

Discovery Timeline

  • 2026-09-28 - CVE-2026-82933 published to the National Vulnerability Database
  • 2026-09-28 - Last updated in NVD database

Technical Details for CVE-2026-82933

Vulnerability Analysis

The mH-DEVELOPER smart home module exposes its management web interface and REST API over plaintext HTTP. All HTTP requests and responses, including those carrying authentication material and control commands, are transmitted without transport-layer encryption. An attacker on the same wired or wireless segment can observe these flows using passive sniffing or active ARP spoofing. Captured credentials grant persistent access to the module, while captured session tokens allow immediate session hijacking without replaying login credentials.

Because device commands also flow in cleartext, an attacker can perform targeted command injection against physical outputs managed by the smart home module. Compromise therefore extends beyond data exposure to direct manipulation of connected relays, lighting, HVAC, and other actuators.

Root Cause

The root cause is the absence of Transport Layer Security (TLS) on the module's HTTP listener. The firmware ships without an HTTPS endpoint and does not enforce certificate-based transport protection, leaving all authentication and command traffic observable to any party on the adjacent network. This is a design-level insecure communication flaw rather than an implementation bug in a specific endpoint.

Attack Vector

Exploitation requires network adjacency, typically a shared LAN or Wi-Fi segment. An attacker runs a packet capture tool such as tcpdump or Wireshark and filters for HTTP traffic to the module's IP address. Authentication payloads containing usernames, passwords, and bearer or cookie-based session tokens are extracted directly from the capture. The attacker then replays the token in a browser or curl request to assume the victim's session and submit device-control API calls. Active techniques such as ARP cache poisoning or rogue access points extend the attack to switched or wireless networks. See the CERT PL advisory for the vendor coordination context and the MH Developer product overview for product details.

Detection Methods for CVE-2026-82933

Indicators of Compromise

  • Unexpected HTTP POST requests to /login or API endpoints on the module from unknown source IP addresses on the local network
  • Concurrent sessions originating from different MAC addresses using the same authentication token
  • Device commands issued outside of normal operator hours or from workstations that do not usually administer the module

Detection Strategies

  • Inspect network traffic for cleartext HTTP sessions destined for smart home module IP addresses and flag any authentication payloads observed in plaintext
  • Correlate ARP table changes on the operational technology (OT) VLAN with new HTTP sessions to the module to identify man-in-the-middle positioning
  • Baseline normal API call patterns and alert on anomalous command sequences, unusual source addresses, or token reuse across endpoints

Monitoring Recommendations

  • Forward switch and wireless controller logs, DHCP leases, and ARP events into a centralized data lake for correlation with device access logs
  • Monitor for promiscuous-mode interfaces or new span sessions on switches serving the smart home VLAN
  • Alert on any HTTP (not HTTPS) traffic to the module after the patch is deployed, which indicates misconfiguration or rollback

How to Mitigate CVE-2026-82933

Immediate Actions Required

  • Upgrade all mH-DEVELOPER smart home modules to version 3.0.30 or later
  • Rotate all passwords and invalidate active session tokens on the module after upgrade
  • Segment the module onto a dedicated management VLAN with restricted inbound access from user networks

Patch Information

The vendor addressed CVE-2026-82933 in version 3.0.30 of the mH-DEVELOPER firmware. The fix introduces encrypted transport for the web interface and API traffic, preventing cleartext exposure of credentials, tokens, and commands. Administrators should verify the running version through the management interface and confirm that HTTPS is enforced after the upgrade. Reference the CERT PL coordinated disclosure post for related vendor guidance.

Workarounds

  • Restrict access to the module's management interface using firewall rules that permit only trusted administrative hosts
  • Require administrators to connect over a VPN or IPsec tunnel when managing the module remotely
  • Disable wireless access to the segment hosting the module, or enforce WPA3-Enterprise with client isolation to limit sniffing opportunities
  • Monitor the adjacent network with intrusion detection sensors to flag ARP spoofing and rogue DHCP activity
bash
# Example firewall policy restricting HTTP access to the module
# Replace 10.10.20.5 with the module IP and 10.10.99.10 with the admin workstation
iptables -A FORWARD -p tcp -s 10.10.99.10 -d 10.10.20.5 --dport 80 -j ACCEPT
iptables -A FORWARD -p tcp -d 10.10.20.5 --dport 80 -j DROP

Disclaimer: This content was generated using AI. While we strive for accuracy, please verify critical information with official sources.

Sources: National Vulnerability Database, CISA KEV, Exploit-DB

Experience the Most Advanced Cybersecurity Platform

See how the world’s most intelligent, autonomous cybersecurity platform can protect your organization today and into the future.