Skip to main content
Vulnerability Database/CVE-2026-100296

CVE-2026-100296: Anjvision YSSD-RTMP-H5 Auth Bypass Flaw

CVE-2026-100296 is an authentication bypass vulnerability in Anjvision YSSD-RTMP-H5 firmware that allows any authenticated user to reset admin credentials to defaults. This article covers technical details, affected versions, impact, and mitigation strategies.

Published:

Disclaimer: This content was generated using AI. While we strive for accuracy, please verify critical information with official sources.

Sources: National Vulnerability Database, CISA KEV, Exploit-DB

CVE-2026-100296 Overview

CVE-2026-100296 affects the Anjvision YSSD-RTMP-H5 IP camera firmware version 3.3.2.4. An empty-body HTTP POST to the /setUserConfig endpoint, routed through the device's SOAP-RPC handler, silently resets the administrator password to its default value. The same request corrupts the in-memory authentication state until the device reloads. The handler does not verify the caller's privilege level, so any authenticated user account, including low-privilege ones, can invoke the operation and take over the administrator identity.

Critical Impact

Any authenticated user can reset the admin password to default and hijack administrative control of the camera with a single empty POST request.

Affected Products

  • Anjvision YSSD-RTMP-H5 firmware version 3.3.2.4
  • Devices exposing the SOAP-RPC web management interface
  • Deployments where non-administrator user accounts exist on the device

Discovery Timeline

  • 2026-09-29 - CVE-2026-100296 published to the National Vulnerability Database (NVD)
  • 2026-09-29 - Last updated in NVD database
  • 2026-09-29 - CISA ICS Advisory ICSA-26-272-05 published

Technical Details for CVE-2026-100296

Vulnerability Analysis

The flaw resides in the SOAP-RPC dispatcher that services the /setUserConfig endpoint on the camera's embedded web server. The handler accepts an HTTP POST with an empty request body and treats the absence of parameters as an instruction to restore defaults for the user configuration structure. The administrator password field is reinitialized to the vendor default value, and the running authentication state held in memory is left inconsistent until the device reboots. This class of issue is tracked as improper check for unusual or exceptional conditions [CWE-754]. The impact is a full compromise of device integrity and availability without affecting confidentiality of stored media, since the attacker gains administrative control and can reconfigure or disable the camera.

Root Cause

The SOAP-RPC handler does not validate two preconditions before mutating persistent user state. First, it does not require a non-empty body carrying explicit parameters. Second, it does not verify that the authenticated session holds administrator privileges. The combination causes an unauthenticated-by-privilege state change from any valid session.

Attack Vector

An attacker with any authenticated account, including a viewer-level user, sends a single empty POST to /setUserConfig over the network. The device silently downgrades the admin password to the default. The attacker then authenticates as admin using known factory credentials and gains full control of the camera.

No verified exploit code is published. Refer to the CISA ICS Advisory ICSA-26-272-05 for the coordinated technical write-up.

Detect Identity Attacks the Moment Authentication Fails

Singularity™ Identity surfaces credential misuse, lateral movement, and privilege escalation in real time, so you can contain the breach before it spreads.

Stop Identity Attacks

Detection Methods for CVE-2026-100296

Indicators of Compromise

  • HTTP POST requests to /setUserConfig with Content-Length: 0 or an empty body originating from internal user sessions.
  • Unexpected successful admin logins from source IPs that previously authenticated only as lower-privilege users.
  • Camera configuration changes, firmware reflashes, or RTMP stream redirection performed shortly after an empty POST to the user configuration endpoint.

Detection Strategies

  • Inspect web server and reverse-proxy logs for POST requests to /setUserConfig where the body length is zero and correlate with the session's user role.
  • Alert on administrator password changes that are not preceded by an interactive admin session on the device management UI.
  • Baseline SOAP-RPC traffic to the camera and flag deviations, particularly writes to user or account configuration methods from non-admin accounts.

Monitoring Recommendations

  • Forward camera and network device logs to a centralized analytics platform for correlation across user sessions and configuration events.
  • Monitor for authentication events using the vendor default admin credential set, which should never appear after initial provisioning.
  • Track device reboots that follow administrative changes, since the in-memory authentication state is only reconciled after a reload.

How to Mitigate CVE-2026-100296

Immediate Actions Required

  • Restrict management-plane access to the camera to a dedicated VLAN reachable only by authorized operators.
  • Remove or disable any non-essential user accounts on affected YSSD-RTMP-H5 devices to reduce the pool of accounts that can trigger the handler.
  • Rotate the administrator password after applying network restrictions and verify the current value is not the factory default.

Patch Information

No vendor patch is referenced in the NVD entry for firmware version 3.3.2.4 at time of publication. Consult the CISA ICS Advisory ICSA-26-272-05 for the latest vendor coordination status and any firmware updates released by Anjvision.

Workarounds

  • Block external access to the camera's HTTP management interface at the perimeter firewall.
  • Enforce network access control lists that permit POSTs to /setUserConfig only from designated administrator workstations.
  • Reboot the device after any suspected exploitation attempt to force reconciliation of the in-memory authentication state, then verify the admin password.
bash
# Example iptables rule restricting camera management access to a jump host
iptables -A FORWARD -p tcp -d <camera_ip> --dport 80 -s <admin_jump_host_ip> -j ACCEPT
iptables -A FORWARD -p tcp -d <camera_ip> --dport 80 -j DROP

Disclaimer: This content was generated using AI. While we strive for accuracy, please verify critical information with official sources.

Sources: National Vulnerability Database, CISA KEV, Exploit-DB

Experience the Most Advanced Cybersecurity Platform

See how the world’s most intelligent, autonomous cybersecurity platform can protect your organization today and into the future.