Skip to main content
Vulnerability Database/CVE-2026-104018

CVE-2026-104018: Wind River VxWorks 7 Privilege Escalation

CVE-2026-104018 is a privilege escalation flaw in Wind River VxWorks 7 command shell that enables authenticated users to bypass privilege checks and execute unauthorized commands. This article covers technical details, affected versions, security impact, and mitigation strategies.

Published:

Disclaimer: This content was generated using AI. While we strive for accuracy, please verify critical information with official sources.

Sources: National Vulnerability Database, CISA KEV, Exploit-DB

CVE-2026-104018 Overview

CVE-2026-104018 is an improper privilege management vulnerability [CWE-269] in the command shell of Wind River VxWorks 7. The flaw affects deployments configured to enforce per-user command privileges. Under certain shell operations, the shell evaluates a command without applying the standard privilege check. An authenticated user with limited privileges can execute commands they are not authorized to run.

Successful exploitation leads to privilege escalation with impact to confidentiality, integrity, and availability of the affected device. The issue affects all versions of VxWorks 7 prior to 26.09 and is fixed in 26.09.

Critical Impact

An authenticated low-privilege user can escalate to unauthorized command execution on VxWorks 7 devices, compromising embedded and safety-critical systems.

Affected Products

  • Wind River VxWorks 7 (all versions prior to 26.09)
  • VxWorks 7 deployments configured to enforce per-user command shell privileges
  • Embedded and industrial devices built on vulnerable VxWorks 7 releases

Discovery Timeline

  • 2026-10-01 - CVE-2026-104018 published to NVD
  • 2026-10-02 - Last updated in NVD database

Technical Details for CVE-2026-104018

Vulnerability Analysis

The vulnerability resides in the VxWorks 7 command shell when per-user command privilege enforcement is enabled. The shell is intended to validate the executing user's privilege level against the permissions assigned to each command before dispatching it. Certain shell operations bypass this validation and dispatch commands directly to the handler.

An authenticated user with restricted shell access can invoke privileged commands through the affected shell path. Because VxWorks commonly serves as the operating system for industrial controllers, networking equipment, and embedded safety systems, privilege escalation at the shell layer can expose device configuration, firmware operations, and runtime control.

Root Cause

The root cause is a missing authorization check [CWE-269] in a specific command evaluation path within the shell. When commands traverse that code path, the privilege gate normally applied to interactive shell input is skipped. The handler executes the command using the shell session's effective privilege context rather than enforcing the per-user policy.

Attack Vector

Exploitation requires network access to the VxWorks command shell and valid low-privilege credentials. The attacker authenticates to the shell, then invokes a command through the unchecked evaluation path to run operations outside their assigned privilege set. No user interaction is required beyond the attacker's own session.

No public proof-of-concept exploit code is available. Refer to the Wind River CVE-2026-104018 Advisory for vendor technical details.

Detection Methods for CVE-2026-104018

Indicators of Compromise

  • Shell command execution by user accounts outside their assigned privilege scope
  • Unexpected configuration changes, firmware operations, or diagnostic command use from low-privileged sessions
  • Shell audit records showing privileged command invocations without corresponding privilege elevation events

Detection Strategies

  • Enable VxWorks shell command auditing and forward logs to a centralized SIEM for correlation against the per-user privilege policy
  • Baseline the set of commands each shell account normally issues and alert on deviations toward administrative commands
  • Monitor authentication events on VxWorks management interfaces for low-privileged sessions that subsequently execute sensitive operations

Monitoring Recommendations

  • Ingest VxWorks shell and authentication logs into a centralized log platform with retention sufficient for post-incident review
  • Alert on repeated failed command executions followed by a successful execution of the same command by the same user
  • Track configuration state of embedded devices and alert on drift that cannot be mapped to an authorized administrator session

How to Mitigate CVE-2026-104018

Immediate Actions Required

  • Upgrade all VxWorks 7 systems to version 26.09 or later, which contains the fix
  • Inventory devices running VxWorks 7 and prioritize those exposing the command shell to networks reachable by non-administrators
  • Rotate credentials for all shell accounts after patching, particularly accounts shared across devices

Patch Information

Wind River has released a fix in VxWorks 7 version 26.09. All versions prior to 26.09 are affected. See the Wind River CVE-2026-104018 Advisory for product-specific patch delivery and build integration guidance.

Workarounds

  • Restrict network access to the VxWorks command shell using firewall rules, management VLANs, or jump hosts until patching is complete
  • Disable or remove low-privilege shell accounts that do not require interactive access to the device
  • Enforce strong authentication and session timeouts on shell interfaces to reduce the exposure window for authenticated attackers

Disclaimer: This content was generated using AI. While we strive for accuracy, please verify critical information with official sources.

Sources: National Vulnerability Database, CISA KEV, Exploit-DB

Experience the Most Advanced Cybersecurity Platform

See how the world’s most intelligent, autonomous cybersecurity platform can protect your organization today and into the future.