Skip to main content

CVE-2026-6232: Semtech LR11xx Buffer Overflow Vulnerability

CVE-2026-6232 is a buffer overflow flaw in Semtech LR11xx transceiver firmware that allows writing arbitrary bytes past buffer bounds via SPI interface. This post explains its impact, affected versions, and mitigation steps.

Published:

Disclaimer: This content was generated using AI. While we strive for accuracy, please verify critical information with official sources.

Sources: National Vulnerability Database, CISA KEV, Exploit-DB

CVE-2026-6232 Overview

CVE-2026-6232 is an out-of-bounds write vulnerability [CWE-787] in the Serial Peripheral Interface (SPI) host command interface of Semtech's LR11xx transceiver firmware. A crafted SPI host command with an oversized length field causes the firmware to write up to 254 arbitrary bytes past the bounds of an internal, non-persistent memory buffer. Exploitation requires physical access to the device and logical access to the SPI bus. The flaw can corrupt adjacent firmware memory, impacting the integrity and availability of the transceiver without directly disclosing data.

Critical Impact

An attacker with physical access to the SPI bus can corrupt firmware memory by sending a single malformed host command, enabling denial of service or firmware state manipulation on affected LR11xx transceivers.

Affected Products

  • Semtech LR11xx transceiver firmware (SPI host command interface)
  • Devices integrating the LR11xx long-range radio transceiver family
  • IoT and LoRa-based endpoints relying on vulnerable LR11xx firmware revisions

Discovery Timeline

  • 2026-10-12 - CVE-2026-6232 published to the National Vulnerability Database (NVD)
  • 2026-10-15 - Last updated in NVD database

Technical Details for CVE-2026-6232

Vulnerability Analysis

The LR11xx firmware exposes a command interface over SPI that accepts host-issued commands containing a length field followed by a payload. The firmware trusts the attacker-controlled length field when copying payload data into an internal buffer. When the length exceeds the buffer's capacity, the firmware writes up to 254 bytes beyond the buffer boundary into adjacent runtime memory. Because the buffer is non-persistent, the corruption affects only the running firmware state and does not persist across power cycles. However, an attacker can repeatedly overwrite memory to influence firmware control structures, variables, or function pointers in RAM.

Root Cause

The root cause is missing bounds validation on the length field of incoming SPI host commands. The firmware copy routine uses the untrusted length value directly as a copy size without clamping it to the destination buffer size. This classic unchecked length condition maps to CWE-787 (Out-of-bounds Write).

Attack Vector

Exploitation is physical. An attacker must open the device enclosure, attach to the SPI bus connecting the host microcontroller to the LR11xx transceiver, and transmit a malformed command frame. The attack targets firmware integrity and availability (VI:H/VA:H) but does not expose confidential data (VC:N). The vulnerability cannot be reached remotely over the radio interface or through network protocols.

No verified public exploit code is available. Refer to the Semtech Security Advisory SEM-PSA-2026-002 for authoritative technical detail.

Detection Methods for CVE-2026-6232

Indicators of Compromise

  • Unexpected transceiver resets, radio stack hangs, or firmware watchdog reboots on devices integrating the LR11xx
  • Evidence of enclosure tampering, exposed debug headers, or attached test clips on SPI lines
  • Anomalous SPI command frames containing length fields larger than documented maximum payload sizes

Detection Strategies

  • Instrument the host microcontroller to log and reject outbound SPI commands whose length fields exceed documented LR11xx command sizes
  • Enable firmware-side runtime integrity checks or watchdog monitoring to flag abnormal transceiver state transitions
  • Correlate device telemetry showing repeated transceiver reinitialization with physical security events from fleet monitoring

Monitoring Recommendations

  • Centralize device health telemetry and alert on sustained increases in LR11xx reset or error counters across fleets
  • Monitor physical access logs and tamper switches for deployed IoT and LoRa endpoints
  • Track firmware versions across the fleet to confirm patched LR11xx firmware is deployed and consistent

How to Mitigate CVE-2026-6232

Immediate Actions Required

  • Review the Semtech Security Advisory SEM-PSA-2026-002 and inventory all devices using LR11xx transceivers
  • Apply the vendor-supplied firmware update to affected LR11xx devices as soon as it is available for your integration
  • Harden physical security for deployed endpoints, including tamper-evident enclosures and restricted maintenance access

Patch Information

Semtech documents the fix and affected firmware revisions in Semtech Security Advisory SEM-PSA-2026-002. Device integrators should coordinate with Semtech or their module supplier to obtain a firmware image that validates SPI host command length fields before copying payload data.

Workarounds

  • Enforce length validation in the host microcontroller driver so malformed SPI commands never reach the LR11xx
  • Deploy tamper detection and physical security controls to deter attackers from attaching to the SPI bus
  • Restrict device deployment to monitored environments where physical access is logged and alerted on

Disclaimer: This content was generated using AI. While we strive for accuracy, please verify critical information with official sources.

Sources: National Vulnerability Database, CISA KEV, Exploit-DB

Experience the Most Advanced Cybersecurity Platform

See how the world’s most intelligent, autonomous cybersecurity platform can protect your organization today and into the future.